ZRC-KX-HA-FFP-1*2*1.5補償導線介紹

Introduction to ZRC-KX-HA-FFP-1 * 2 * 1.5 Compensation Wire

一般用聚氯乙烯絕緣和護套補償導線或電纜具有優良的防潮、耐磨及阻燃特性；耐高溫氟塑料絕緣和護套補償導線或電纜采用連續擠出工藝，更有耐高溫、耐寒、耐酸堿油水、不延燃、抗老化等*性，產品質量高于國標GB/T4989-94(等效采用IEC584-3)的規定。

Generally, PVC insulated and sheathed compensating wires or cables have excellent moisture-proof, wear-resistant, and flame-retardant properties; High temperature resistant fluoroplastic insulated and sheathed compensation conductor or cable adopts continuous extrusion process, which is more resistant to high temperature, cold, acid, alkali, oil, water, non flame, aging, etc. The product quality is higher than the provisions of the national standard GB/T4989-94 (equivalent to IEC584-3).

ZRC-KX-HA-FFP-1*2*1.5補償導線它是在一定溫度范圍內（包括常溫）具有與所匹配的熱電偶的熱電動勢的標稱值相同的一對帶有絕緣層的導線，用它們連接熱電偶與測量裝置，以補償它們與熱電偶連接處的溫度變化所產生的誤差。分為延長型和補償型兩種。

ZRC-KX-HA-FFP-1 * 2 * 1.5 compensation wire is a pair of insulated wires with the same nominal value of thermoelectric potential as the matched thermocouple within a certain temperature range (including room temperature). They are used to connect the thermocouple and the measuring device to compensate for the error caused by temperature changes at the connection point between them and the thermocouple. It is divided into two types: extension type and compensation type.

補償導線使用特性

Characteristics of compensating wire usage

1． 導體zui高工作溫度：耐熱級：聚全氟乙丙烯(F46)200℃

1. Conductor maximum operating temperature: heat-resistant grade: perfluoroalkoxy (F46) 200 ℃

可溶性聚四氟乙烯260℃，，，，硅橡膠180℃

Soluble polytetrafluoroethylene 260 ℃, silicone rubber 180 ℃

普通級：聚氯乙烯70℃和105℃，交聯聚乙烯90℃

Ordinary grade: polyvinyl chloride at 70 ℃ and 105 ℃, cross-linked polyethylene at 90 ℃

低煙無鹵阻燃聚烯烴70℃，交聯型90℃和125℃

Low smoke halogen-free flame-retardant polyolefin at 70 ℃, cross-linked at 90 ℃ and 125 ℃

2． 低環境溫度：聚氯乙烯護套：固定敷設-40℃，非固定敷設-15℃

2. Low ambient temperature: PVC sheath: fixed installation -40 ℃, non fixed installation -15 ℃

氟塑料絕緣和護套：固定敷設-60℃，非固定敷設-20℃

Fluoroplastic insulation and sheath: fixed installation -60 ℃, non fixed installation -20 ℃

3． 電纜允許彎曲半徑： 非鎧裝電纜zui小為外徑的6倍

3. Allowable bending radius for cables: The minimum allowable bending radius for non armored cables is 6 times the outer diameter

銅帶屏蔽或鋼帶鎧裝點纜zui小為電纜外徑的12倍

Copper tape shielding or steel tape armor point cable with a minimum diameter of 12 times the outer diameter of the cable

氟塑料絕緣和護套zui小為電纜外徑的10倍.

Fluoroplastic insulation and sheath are as small as 10 times the outer diameter of the cable